Difference between revisions of "Software Configuration/it"

From Click Wiki
Jump to: navigation, search
(Created page with "Al primo avvio dopo l'installazione è necessario configurare il software 1Click. Questa prima configurazione è completamente guidata e permette all'utente di essere immediat...")
(Created page with "=Impostare il File di Configurazione=")
Line 3: Line 3:
 
Al primo avvio dopo l'installazione è necessario configurare il software 1Click. Questa prima configurazione è completamente guidata e permette all'utente di essere immediatamente operativo e inviare i file nel giro di qualche minuto.
 
Al primo avvio dopo l'installazione è necessario configurare il software 1Click. Questa prima configurazione è completamente guidata e permette all'utente di essere immediatamente operativo e inviare i file nel giro di qualche minuto.
  
=Setting the Configuration File=
+
=Impostare il File di Configurazione=
  
 
The first step of the process allows to set the configuration file of the Scanner. The Configuration file holds all the information on the various components of the user's specific scanner, therefore it is crucial for the functioning of the system.
 
The first step of the process allows to set the configuration file of the Scanner. The Configuration file holds all the information on the various components of the user's specific scanner, therefore it is crucial for the functioning of the system.

Revision as of 10:08, 9 June 2017

Warning: Display title "First Software Configuration" overrides earlier display title "Configurazione del Software".

Al primo avvio dopo l'installazione è necessario configurare il software 1Click. Questa prima configurazione è completamente guidata e permette all'utente di essere immediatamente operativo e inviare i file nel giro di qualche minuto.

Impostare il File di Configurazione

The first step of the process allows to set the configuration file of the Scanner. The Configuration file holds all the information on the various components of the user's specific scanner, therefore it is crucial for the functioning of the system.

LoadConf.PNG

To set it, make sure that the scanner is correctly connected and switched on and click on the Get From Scanner button to load it automatically.

LoadedConf.PNG

Once the file has been succesfully loaded, in the box will be shown:

  • the scanner's serial number
  • the scanner's components

It is also possible to load a configuration from and external file, using the button Load From File, though this kind of operation will be performed in very rare cases (for instance if Open Technologies had to modify the configuration file of the scanner and the internal file is no longer valid).

Click next in the dialog to follow with the configuration, click Cancel to abort.

System Calibration

The following step is the System Calibration starting with the Optical Head and then calibrating the movement system.

Head Calibration

In order to proceed, the calibration kit .xml file must be loaded, by clicking on the buttonLoad Calibration Kit from File.

LoadCal.PNG

This .xml file can be found in the scanner's internal memory, identified by the computer as if it were a Usb flash drive.

CalKitLocation.PNG

NOTE: CHECK THAT THE NUMBER OF THE FILE AND THE NUMBER OF THE PLATE YOU HAVE IN THE ACCESSORIES BOX COINCIDE. IF THEY DO NOT CONTACT YOUR DEALER BEFORE CALIBRATING

To insert the calibration plate in the scanner, detach the black support on the back of the plate simply by pulling, as it is held by magnets.

Master-click.jpg

Release the two screws of the impression holder and insert the master support, tightening the screws as much as possible to fix it properly.

Supporto-master.png

Place the calibration plate in the scanner taking care in positioning it keeping the part with one bold dot on the left and the side with two bold dots on the right.

MasterinScanner.png

Click the button Head Calibration to start calibration.

Movement System Calibration

To follow with the movement system calibration insert an impression in the scanner as shown in the image and click on the button Movement Calibration

MovCal.PNG

Click next in the dialog to follow with the configuration, click Cancel to abort.

Set the Trimming

In this step the user can configure an automatic trimming that will automatically erase all the information located under the scan height plane.

Move the slider on the bar in the dialog to modify the scan height, taking particular care in not colliding with essential parts of the impression.

Trimming.png

Click next in the dialog to end the first configuration procedure.

Dental 2 5 wiz prev.png 120px-Homebutton.png Dental 2 5 wiz next.png